Bunn ES.2C Guía para resolver problemas

INSTALLATION & OPERATING MANUALBUNN-O-MATIC CORPORATIONPOST OFFICE BOX 3227SPRINGFIELD, ILLINOIS 62708-3227PHONE: (217) 529-6601 FAX: (217) 529

10PROGRAMMING THE DISPENSEROpen the dispenser door to access the digital programming module with LED display.Two basic modes are available to the oper

11 Decaf Dispense Ration Regular Dispense Ration Decaf Espresso Ration Regular Espresso Ration Empty Product Threshold Small Cup Dispe

12MENU (-) (+)MENU (-) (+)Decanter Dispense Time Powder Whipper Delay Off Powder Auger Motor Delay on Rinse Required time Small Espresso

13PROGRAMMING (Continued) LCD DISPLAY PROGRAM MODE DESCRIPTIONProgram Mode: Used to change or enter new set-up values.To enter the Program Mode,

14PROGRAMMING (Continued) LCD DISPLAY PROGRAM MODE DESCRIPTIONMENU (-) (+)603 8MENU (-) (+)703 8MENU (-) (+)801 0MENU (-) (+)901 0MENU (-) (+)014

15PROGRAMMING (Continued) LCD DISPLAY PROGRAM MODE DESCRIPTIONMENU (-) (+)418MENU (-) (+)515MENU (-) (+)612 4MENU (-) (+)710MENU (-) (+)810MENU (

16PRIMING THE CONCENTRATE LINES 1. Open the dispenser door.2. Select Prime on the Function Selector Switch and Run on the Mode Selector Switch. 3.

17DRAINING THE HOT WATER TANKCAUTION - The dispenser must be disconnected from the power source throughout these steps1. Disconnect the dispenser fro

18CLEANING & PREVENTATIVE MAINTENANCE General Cleaning and Sanitizing Procedures Note: The BUNN¨ SLCC-6 dispenser incorporates a “user select-able

19Weekly: Parts Washing and Sanitizing11. When reassembling parts, be sure to align ar-row on frother disk with flat on whipper motor shaft, and r

2BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTYBunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:1) All equipment other than as s

20REPLACING THE PUMP TUBINGThe pumps and tubing used in the dispenser are designed to give maximum performance and long life. However, the tubes are a

21CALIBRATING THE DISPENSERNOTE: The SLCC-6 is calibrated at the factory and does not normally need to be re-calibrated. To enter the Calibration Mode

22 LCD DISPLAY CALIBRATION MODE DESCRIPTIONMENU (-) (+)4Cr u nMENU (-) (+)4C4 1MENU (-) (+)5C0 3 5MENU (-) (+)6CE 0 0MENU (-) (+)7C- -MENU (-) (+

23TROUBLESHOOTING GUIDE Error Codes When an error has occurred, all Door LED’s will be flashing. Open the Door to access the LED Display and re-cord th

24TROUBLESHOOTING GUIDE (Continued) LCD DISPLAY ERROR DESCRIPTION/TROUBLESHOOTINGMENU (-) (+)CE0 0 7MENU (-) (+)CE0 0 8MENU (-) (+)CE0 0 9MENU (-)

25Field Calibration of the Concentrate Pumps, Dispenser Flow Rates,and Hopper Powder ThrowThe factory set default values for the Pump & Dispenser

26Calibrating the Dispenser Flow RatesDecaf Coffee - Dispenser Flow Rate Calibration 1. Select RINSE on the Function Selector Switch, and PROGAM of t

27Field Adjustment of Powder HoppersThe powder throw for the powder products is pre-set from the factory. It can be checked and adjusted in the field

28ELECTRICAL WIRING DIAGRAM SLCC-639328 0126071581510151510152020151014151012DUAL VOLTAGE BLOWER FAN115+V+V-V-VGNDN/L2L1COMN.O.MAIN CONTROL BOARDJ15J3

29ELECTRICAL WIRING DIAGRAM SLCC-639328 0126071581510151510152020151014151012115+V+V-V-VGNDN/L2L1COMN.O.MAIN CONTROL BOARDJ15J3J111J6J5J11315123456789

3INTRODUCTIONThis equipment dispenses hot beverages or soups on demand from powdered product. It is indoor use only on a sturdy counter or shelf.TABLE

4This equipment must be installed to comply with the Basic Plumbing Code of the Building Officials and Code Administrators International, Inc

5INITIAL SET-UP1. Apply the four non-skid pads from the parts box to the bottom of the legs.2. Remove the drip tray assembly and drip tray bracket f

6OPERATING CONTROLS AND INTERFACE1. Carafe Button: Momentary pushed to select carafe size dispense of coffee.2. Stop Button: Momentary pushed to sto

71314 11 128 4 1 5 2 6 3 679OPERATING CONTROLS (Continued)393

8INSTALLING PUMP TUBING1. Loosen the thumbscrews securing the tubing retainer plates to the pump bodies and set the retainer plates aside.2. Depress

9INITIAL FILL & HEAT1. Turn on the water supply and connect the dispenser to the power source. 2. Water will automatically flow into the tank to